1A sail is a wing
Hold your hand flat out of a car window and tilt the front up a little. The air lifts your hand. Tilt it too much and the air just pushes it back.
A sail works the same way. It is a wing standing on its end. When the wind flows smoothly round both sides, it pulls the sail sideways and a bit forwards.
Let the sail out too far and it flaps: no pull. Pull it in too far and the wind can’t follow the curve behind it: it just pushes. In between, the sail pulls hardest. The little ribbons on the sail, called telltales, show you which is which.
A sail is a wing: a curved surface that turns the air flowing past it. Turning the air takes force, and the air pushes back on the sail. Most of that force is lift, at right angles to the wind; a smaller part is drag, along the wind.
Both depend on the angle of attack, the angle between the sail and the wind. Too small and the luff lifts and flaps: luffing. Too big and the flow can’t follow the curve on the leeward side; it breaks away into eddies: stall. Lift drops and drag climbs. In between, at roughly 8° to 22° for a sail of normal depth, the flow stays attached on both sides and the sail gives the most lift for its drag.
Telltales show it: the windward one lifts when you luff, the leeward one droops when you stall.
You may have heard that the air over the curved side has to catch up with the air underneath, so it goes faster. It doesn’t have to. The air on the leeward side does go faster, but it reaches the leech well before the air on the windward side. Lift comes from the sail turning the flow.
Thin-aerofoil theory is the starting point: CL ≈ 2π(α − α0), where camber makes the zero-lift angle α0 negative, so a deep sail lifts even at zero incidence. Lift per metre of span is L = ρUΓ (Kutta–Joukowski), with the circulation Γ fixed by the Kutta condition: the flow leaves the leech smoothly. The airflow in these pictures is computed exactly that way, as a lattice of vortices along the sail.
A real sail is a low-aspect-ratio wing (AR around 3 to 4), so its lift slope is well below 2π and it pays induced drag, CDi = CL² / (π e AR): the cost of the vortices shed at the head and the foot. Past the stall the leeward flow separates, progressively from the leech forward as the angle grows; the leeward telltales near the leech go first.
The force numbers come from the same section model as Pro-Extreme: lift rises from the luff angle (2° + 30 × depth) to CLmax = (1.1 + 3.2(depth − 0.08))(1 + 0.35(draft − 0.45)) at the stall angle (14° + 60 × depth), then blends into a flat plate.
2The wind the boat feels
On a bike you feel wind on your face, even on a still day. A moving boat makes its own wind too. It mixes with the real wind, and the sail feels the mix.
As the boat speeds up, that mixed wind swings round towards the front of the boat. That’s why you pull the sails in as the boat gets going.
The sail sees the apparent wind: the true wind plus the wind of the boat’s own motion, which blows straight from ahead. Upwind it is stronger than the true wind; downwind it is weaker. It always comes from further forward than the true wind.
Sails are trimmed to the apparent wind, and the telltales and the burgee show it. Speed up, and you trim in.
Apparent wind is a vector sum: AW = TW − V. For a true wind angle βT and a speed ratio k = V / TWS, the apparent angle is βA = atan2(sin βT, cos βT + k).
Fast boats sail with the apparent wind forward of the beam even when heading downwind. The wind gradient adds a twist: higher up the true wind is stronger, so the apparent wind there comes from further aft. That is one reason sails are set with twist.
3One sail on the water
The sail pulls the boat forward, but it also pushes it sideways, a lot. Under the boat is the centreboard (or daggerboard): a flat fin that grips the water. It stops the boat sliding sideways, so the forward pull wins and the boat moves ahead. Pull the board up and the boat slides sideways like a skateboard on ice.
The sideways push also tips the boat over. You lean out on the high side to keep her flat. A flat boat is a fast boat.
And you can’t sail straight into the wind: the sail just flaps. To get upwind, you zigzag.
Split the sail’s force two ways: drive along the boat’s heading, and side force across it. Close-hauled, side force is three or four times the drive.
The board balances it. It is a second wing, in the water, and like the sail it needs an angle of attack, so the boat always slides a few degrees sideways: leeway. More board, less leeway.
The side force acts high on the sail and the board’s force low down, so together they heel the boat; the crew’s weight out to windward rights it. Where the two forces sit also steers the boat: when the sail’s push is behind the board’s grip, she turns into the wind (weather helm).
Drive pushes the boat until it meets the water’s resistance, which climbs steeply near hull speed. Inside about 40° of the true wind no trim gives drive: the no-go zone.
In steady sailing the forces balance in pairs: aerodynamic drive equals hull resistance; side force equals foil lift; the heeling moment equals the righting moment; and the yawing moments balance with a little rudder.
The course theorem ties it together: the angle between the course and the apparent wind equals the sail’s drag angle plus the hull’s drag angle, β = εA + εH, where tan ε = drag / lift for each. To point higher, cut drag on either side: a cleaner sail, or a cleaner hull and foils. The picture works out both angles live.
Leeway follows from the foils’ lift curve: the side force fixes the foil lift coefficient needed, so less board area means more leeway and more induced drag for the same side force. Heel tilts the sail force: the useful part falls with cos(heel), and the heeling moment grows with the height of the centre of effort. The boat in the picture is an ILCA 7 with a 65 kg sailor, using Pro-Extreme’s full force model.
4Two sails together
The jib is the small sail at the front. The jib and the mainsail help each other. The jib bends the wind so it meets the mainsail more from the front, and the mainsail helps the jib work closer to the wind. Together they pull more than the mainsail alone.
But if you pull the jib in much tighter than the mainsail, it blows its wind onto the back of the mainsail and spoils it. Trim them as a team.
Two sails close together change each other’s wind. The main, by turning the flow, makes the wind ahead of it come from further forward (upwash): the jib sails in that lifted wind, so it can point higher. The jib in turn makes the wind at the main’s luff come from further aft: the main is headed, so it can be sheeted closer without stalling, and its luff is less touchy.
The gap between them, the slot, matters. If the jib is sheeted much harder than the main, its air pours onto the main’s leeward luff: backwinding, and the main loses power.
The old explanation, that the slot squeezes the air and speeds it onto the main, has it backwards. The air in the slot slows down. What gains is the jib: the main lets the air leave the jib’s leech faster, which keeps the jib’s flow attached.
Arvel Gentry’s analyses of the flow round sail pairs in the 1970s set the modern picture. The main’s circulation creates upwash ahead of it, lifting the jib’s apparent wind, so the jib carries more lift at the same sheeting angle. The jib’s circulation creates downwash at the main’s luff, lowering the main’s effective angle of attack and its leading-edge suction peak, so the main stalls later. And the main raises the flow speed at the jib’s leech (the “dumping velocity”), so the jib’s leeward flow has less pressure to recover and stays attached. The pair carries more lift than the two sails apart, with the gain going mostly to the jib.
The picture’s airflow comes from a vortex lattice on both sails, so these effects appear in it directly. The forces come from Pro-Extreme’s model (an RS Quest close-hauled in 12 knots), where the jib’s effect is a reduction of up to 6° in the main’s angle of attack while the jib is drawing, and backwinding when the jib is sheeted much harder than the main.
5Where next
Now steer a boat yourself, then shape its sail.
Put it to work on every point of sail, then shape the sails with every line.
The simulators run the same physics, from the tables up to the full force model.